Basilisk V4 Pro + HyperFlux V2 scroll wheel issue: intermittent scroll wheel failure | Razer Insider
Skip to main content
Question

Basilisk V4 Pro + HyperFlux V2 scroll wheel issue: intermittent scroll wheel failure

  • Oct 30, 2026 5:05 AM UTC
  • 19 replies
  • 254 views

RTsdqq
I'm a player from China. I bought the latest Basilisk V4 Pro together with the new HyperFlux V2 Hard Edition charging pad. The pad has already been replaced once by Razer's official service with a brand-new unit, and the mouse was sent for inspection and returned as "no problem". However, the two still do not work together: with the charging module installed the scroll wheel fails intermittently, and when the mouse is placed on the pad it is basically unusable.

I'm posting here because local support only tested the mouse alone and could not reproduce the combination issue. I'd like to ask whether other players have seen this, and whether Razer engineering can test the full set.

Setup:

- Mouse: Basilisk V4 Pro, firmware 1.03.00 R1

- Charging mat/module: HyperFlux V2 Hard Edition

- Receiver: original 2.4 GHz dongle (NOT the mat's receiver, NOT Mouse Dock V2 Pro, no mixed charging pucks)

- Synapse: 4.0.86.2610281118

- All items are new sealed units. Mouse and mat have already been replaced once; the issue still occurs.

Symptom:

The scroll wheel intermittently stops working during normal use. It is not every time, but after installing the HyperFlux V2 charging module the failure probability increases significantly. When the mouse is placed on the mat for wireless charging, the scroll wheel is basically unusable.

Tests:

1. Charging module installed, mat disconnected, original 2.4 GHz receiver: intermittent scroll failure.

2. Charging module removed, mat disconnected, original 2.4 GHz receiver: scroll wheel works normally.

3. Mouse on HyperFlux V2 mat: scroll wheel unusable.

4. USB-C wired: no scroll failure observed.

5. Firmware updated to 1.03.00 R1: issue persists.

6. Two different new units (mouse/mat replaced): issue persists.

Service history:

The mouse was sent in for inspection. Service tested only the mouse and returned it as "no problem". They did not test the combination of mouse + charging module + mat + original receiver, and a short test cannot catch an intermittent fault. Because support requested inspection, the 7-day no-reason return window expired while the case was delayed.

What I am asking:

- Has anyone else seen scroll wheel failure only when the HyperFlux V2 charging module is installed?

- Is there a correct puck/part number for V4 Pro + HyperFlux V2 Hard Edition that I may have missed?

- Any workaround besides removing the module / not using the mat?

- Razer: please test the complete set, not just the mouse, and provide the test conditions/report.

I can share videos, serial numbers (redacted), order/RMA records and the four test combinations.

This is not a "mouse is dead" post — the mouse works with the module removed. It looks like a charging-module/scroll-wheel interaction or compatibility issue. If you have the same combo, please reply with your experience.

19 Replies

  • Insider Mini
  • Nov 2, 2026 2:21 PM UTC

bro, I got a new mouse from razer which is the second basilisk v4 pro with a different serial number and everything. I have the same issue with or without dongle pairing. I believe this is a firmware or software issue that they have to be on top of.


  • Insider Mini
  • Nov 4, 2026 4:03 PM UTC

Exactly the same problem and combination here. Scrolling randomly stops working. A temporary fix: turn the mouse upside down and you will hear the “click” of the scroll wheel clutch engaing. Fixes it for a minute or so until the problem reoccurs, which it does.

Going to return this POS to Amazon.


  • Insider Mini
  • Nov 4, 2026 8:07 PM UTC

it has to be firmware bro


Monstieur
  • Insider Mini
  • Nov 5, 2026 5:08 AM UTC

I have the same problem with the Basilisk V4 Pro and the HyperFlux V2. Exchanging the mouse did not work either. The Smart Reel function is broken. The wheel gets stuck and stops working till you turn the mouse upside down. It could be some kind of magnetic issue with the HyperFlux V2. Turning off Smart Reel fixes the issue.


Monstieur
  • Insider Mini
  • Nov 5, 2026 7:25 AM UTC

The issue happens only on certain spots on the HyperFlux V2, presumably based on the magnetic field. It happens most frequently in the center, and the mouse actually recovers if you simply move it to the side of the pad. If you remove the wireless charging puck from the mouse, it does not malfunction even on the center of the pad. So it's related to wireless charging and not direct exposure to the pad.


  • Insider Mini
  • Nov 5, 2026 8:23 AM UTC

Yes - disabling Smart Reel fixes it for me too. Or turning the mouse upside down to get the mouse wheel clutch to “engage” again.

 

I also notice the lighting on my mouse gets disabled around about the same time my wheel scroll stops working...


Monstieur
  • Insider Mini
  • Nov 5, 2026 9:01 AM UTC

It is not strictly upside down. Just stopping the charging makes it engage again. Move it to the edge of the pad or lift it up and hold still. Remove the charging puck from the mouse and Smart Reel works perfectly.


Lrbrownii
  • Insider
  • Nov 5, 2026 5:18 PM UTC

Naga v3 pro was doing this. I bet it's the same Synapse issue...


Monstieur
  • Insider Mini
  • Nov 5, 2026 6:03 PM UTC

I don't have the issue on my Naga V3 Pro on the HyperFlux V2. Had the issue with 2 different DeathAdder V4 Pro.


  • Insider Mini
  • Nov 5, 2026 8:53 PM UTC

​@Lrbrownii I have the Naga v3 pro aswell. it works great no issues there for me. I think it’s a software issue I am convinced cause I rebinded the toggle scroll wheel button to my own website.

 

I pressed it a lot and never failed. the hardware works also because when I press the scroll wheel buttons in synapse. going from freescroll to tacticle and stuff. it works. 

 

the button that’s been set by default out of the box doesn’t change the scroll wheel setting for me at all on a replacement unit mouse. that’s why I belive this is a software issue.

 

Razer can fix it. let’s go!


  • Insider Mini
  • Nov 5, 2026 9:58 PM UTC

also the cycle sensetivity button doesn’t work. I mean the button functions. but the software/synapse is not cycling sensitivity stages. I only have two sensitivity stages enabled and it doesn’t cycle trhought them at all.

 

Razer has to fix this aswell


Monstieur
  • Insider Mini
  • Nov 5, 2026 10:21 PM UTC

Use Cycle Sensitivity Stage Up which is a hardware function. It incorrectly shows Synapse required but it works without Synapse.


  • Insider Mini
  • Nov 5, 2026 11:59 PM UTC

​@Monstieur It can’t be a hardware flaw if the button physically works. Which I tested because you can rebind both buttons to a website and I spam click it. It opens a lot of tabs. So it’s definitely a synapse issue/software. The reason that you have said functionality working without synapse is cause it’s probably built in in some way. Or you have a hardware profile enabled that uses a profile which is on the mouse 


Monstieur
  • Insider Mini
  • Nov 6, 2026 12:13 AM UTC

I meant to say Cycle Sensitivity Stage Up is implemented in hardware. The mouse does it internally if Synapse is not running. While Synapse is running I think it overrides the mouse hardware function so it doesn't work.


The issue happens only on certain spots on the HyperFlux V2, presumably based on the magnetic field. It happens most frequently in the center, and the mouse actually recovers if you simply move it to the side of the pad. If you remove the wireless charging puck from the mouse, it does not malfunction even on the center of the pad. So it's related to wireless charging and not direct exposure to the pad.

Thanks for narrowing this down, that center-of-the-mat detail is really useful. If removing the puck fixes it even in the center, that does point to the charging itself rather than the mat surface. It would be great if you could note whether it also happens with the mouse on a different surface while charging, so support has a clear pattern to work from.


I do not have this exact mouse and mat combination myself, but I have had a scroll wheel go intermittent on a wireless mouse before, and it drove me crazy because it worked fine when I plugged it in. Your wired test and the module removed test really stood out to me for that reason. I hope Razer takes the full set seriously, because two replacement units pointing the same way is hard to ignore.


Thanks for sharing that, bibleblessings. That wired versus wireless difference is exactly what makes this case so telling, and your own experience with an intermittent scroll wheel really adds to it. I agree the two replacement units pointing the same way is hard to ignore, so keeping a clear log of when it fails should help support take the full set seriously.


Lrbrownii
  • Insider
  • Nov 7, 2026 7:21 PM UTC

​@Lrbrownii I have the Naga v3 pro aswell. it works great no issues there for me. I think it’s a software issue I am convinced cause I rebinded the toggle scroll wheel button to my own website.

 

I pressed it a lot and never failed. the hardware works also because when I press the scroll wheel buttons in synapse. going from freescroll to tacticle and stuff. it works. 

 

the button that’s been set by default out of the box doesn’t change the scroll wheel setting for me at all on a replacement unit mouse. that’s why I belive this is a software issue.

 

Razer can fix it. let’s go!

I was adding these devices in 3rd party rgb software and noticed a real gap in key input software so I have been doing hardware features in a game launcher/ profile switcher I have been developing. Looks like they did some updates to Synapse. You still can't be connected to Mouse dock pro or Hyperpolling dongle for above 1000hz polling rate and get battery optimization from Hyperflux v2. I can.


Thanks for adding that, Lrbrownii — the Synapse and polling point is useful, especially since several people here are seeing this only on wireless charging and not on wired. For anyone still seeing it, disabling Smart Reel in Synapse is worth trying first, as brak22 and others found that stopped the unwanted scrolling for them, and testing at 1000Hz polling can help narrow down whether the higher rate is part of it. RTsdqq, have you had a chance to try Smart Reel off yet, and does the wheel recover when you move the mouse to the edge of the mat, as Monstieur described? That would help show whether it is the charging position, the Synapse setting, or both.