Hey. I have a razer wolverine chroma v2. After updating the firmware, the controller does not turn on at all! Stuck vibration when connecting. I have made sure the usb-c wire is properly attached and have tried on my other xbox series x and there is still no response. When connecting stuck vibration. There is no connection. Help with the problem? With respect.
Question
Razer Wolverine V2 Chroma after update not working and stuck vibration
The solution to the problem. Plug in the device to your PC and Run the downloaded app from this link https://rzr.to/JUXEHe
AC1950D01900032 wrote:
The solution to the problem. Plug in the device to your PC and Run the downloaded app from this link https://rzr.to/JUXEHe
Did you have any issues with the update not going through? i just tried it and it gets stuck at 100% and the controller disconnects
No. Everything went fine with me. After the update, I connected the gamepad to the console and it updated without freezing.
Hello, I have a similar problem. My controller gives 2x white LED and nothing else The computer does not detect the device
Patryko340 wrote:
Hello, I have a similar problem. My controller gives 2x white LED and nothing else The computer does not detect the device
Download the driver from the link above. Then install it. It will ask you to connect the gamepad. Plug in the gamepad and the update should run. Pardon my English)
AC1950D01900032 wrote:
Patryko340 wrote:
Hello, I have a similar problem. My controller gives 2x white LED and nothing else The computer does not detect the device
Download the driver from the link above. Then install it. It will ask you to connect the gamepad. Plug in the gamepad and the update should run. Pardon my English)
I downloaded this application but nothing happens when I connect the controller . I can't start the update because the computer doesn't see the controller
Patryko340 wrote:
AC1950D01900032 wrote:
Patryko340 wrote:
Hello, I have a similar problem. My controller gives 2x white LED and nothing else The computer does not detect the device
Download the driver from the link above. Then install it. It will ask you to connect the gamepad. Plug in the gamepad and the update should run. Pardon my English)
I downloaded this application but nothing happens when I connect the controller . I can't start the update because the computer doesn't see the controller
Hi. I just turned on the program. She asked to connect the gamepad. I connected the gamepad and turned on the update.
AC1950D01900032 wrote:
Patryko340 wrote:
AC1950D01900032 wrote:
Patryko340 wrote:
Hello, I have a similar problem. My controller gives 2x white LED and nothing else The computer does not detect the device
Download the driver from the link above. Then install it. It will ask you to connect the gamepad. Plug in the gamepad and the update should run. Pardon my English)
I downloaded this application but nothing happens when I connect the controller . I can't start the update because the computer doesn't see the controller
Hi. I just turned on the program. She asked to connect the gamepad. I connected the gamepad and turned on the update.
Do I need to have anything installed, enabled, or a special cable to perform this update?
I will also add that the last time the gamepad worked and was connected to the console, I held the Xbox button and clicked turn off the controller. Maybe that had some influence on its failure. I tried to do an updated On 3 different laptops without success, in each of them the updated button does not light up
Patryko340 wrote:
AC1950D01900032 wrote:
Patryko340 wrote:
AC1950D01900032 wrote:
Patryko340 wrote:
Hello, I have a similar problem. My controller gives 2x white LED and nothing else The computer does not detect the device
Download the driver from the link above. Then install it. It will ask you to connect the gamepad. Plug in the gamepad and the update should run. Pardon my English)
I downloaded this application but nothing happens when I connect the controller . I can't start the update because the computer doesn't see the controller
Hi. I just turned on the program. She asked to connect the gamepad. I connected the gamepad and turned on the update.
Do I need to have anything installed, enabled, or a special cable to perform this update?
I will also add that the last time the gamepad worked and was connected to the console, I held the Xbox button and clicked turn off the controller. Maybe that had some influence on its failure. I tried to do an updated On 3 different laptops without success, in each of them the updated button does not light up
No. I turned on the program first. She asked to connect a Razer gamepad. I connected the gamepad and followed the instructions in the program. Maybe you have a completely different case of breakdown.
I think I found the glitch that's causing my problem. This is probably a rectifier diode marked as k9. Does anyone know where I can find a motherboard diagram?
Reply
Sign up
Already have an account? Login
Log in with Razer ID to create new threads and earn badges.
LOG INEnter your E-mail address. We'll send you an e-mail with instructions to reset your password.