GPU Max Fan Speed While Laptop is Off- EVGA FTW3 Ultra 3080 | Razer Insider
Skip to main content

GPU Max Fan Speed While Laptop is Off- EVGA FTW3 Ultra 3080


Hey all,

Due to some fortunate circumstances I just switched from a FE 3070 to an EVGA FTW3 Ultra 3080 today, but anytime the laptop is turned off or set to hibernate, 2 of the 3 fans on the card kick into maximum speed. This did not happen with the FE 3070 card so I am wondering how I can fix this (beyond the solution of “just turn off the eGPU or unplug it every time” because my ADHD means I’m constantly going to forget to do this).

I’m looking for a software fix, drivers, thunderbolt, etc.

Setup:


  • Dell XPS 15 9570
  • Razer Core X Chroma
  • EVGA FTW3 Ultra 3080

I seriously appreciate any and all help anyone can provide because I’ve spent hours searching forums for an answer and haven’t found one.


*Edit Note: I rearranged which ports the Y-splitter in my eGPU connects to and now all three fans run together at max speed.
Did this topic help you find an answer to your question?
This topic has been closed for comments

Razer.Caziel
  • I am the Lightbringer
  • April 19, 2021
As far as I know, the eGPU only depends on the computer it is connected to. Once that connection is severed when the laptop is powered down, the eGPU should go into a hibernation state of sorts. It is highly likely that your new card incorrectly detects this as a mining type of situation. Do you get the same results when the Thunderbolt cable is unplugged?

Razer.Caziel
As far as I know, the eGPU only depends on the computer it is connected to. Once that connection is severed when the laptop is powered down, the eGPU should go into a hibernation state of sorts. It is highly likely that your new card incorrectly detects this as a mining type of situation. Do you get the same results when the Thunderbolt cable is unplugged?


Unplugging it or powering off the GPU stops the fans from running full speed. I’m wondering if there’s someway to prevent communication over TB3 when the computer is shut down / hibernating (basically treating it like it’s unplugged). Currently I think it’s still communicating over the TB3 even when shut down.

With the FE 3070, the fans didn’t do this (as in I didn’t have to unplug the eGPU).

Hi,

Exact same issue here. Upgraded from a Razer Core 2 to Core X Chroma. Same GPU (1080Ti) and laptop (Razer 15 Advanced 2018)

When my laptop would go to sleep or be shut down fully the Core 2 would go into a full sleep state. But the Core X Chrome (which has an additional power rocker switch) goes into a 100% fan mode on the GPU. So if my laptop sleeps for power saving after 30 minutes for example, then all of a sudden the eGPU goes into an overdrive situation which is a nightmare. (Defeats the point of the laptop going into sleep mode, right?)

Nothing else in my platform changed. It drives me crazy having to manually switch off and on the eGPU every time I want to either shut down my laptop or before I boot it up in the morning. And sleep is no longer an option now.

I have looked for other threads where people have had this issue, very little - and certainly no fixes. I will try anything because now after 3 (otherwise blissful!) years with my Razer set-up this is the only thing that really, really irks me.

Please, Razer Support - help me out here!

Thanks very much.

Kind regards,

James

Razer.Caziel
  • I am the Lightbringer
  • April 20, 2021
Interesting. I don't see any firmware-related solutions from my end. Have you guys tried reinstalling the TB3 drivers? I'd appreciate it if you can send me screenshots of your MSINFO32 and TB3 driver version.

Razer.Caziel
Interesting. I don't see any firmware-related solutions from my end. Have you guys tried reinstalling the TB3 drivers? I'd appreciate it if you can send me screenshots of your MSINFO32 and TB3 driver version.

Hi there, thanks for your help.

I noticed I was on BIOS revision 1.03 for my model of Razer laptop, which I have now just updated to version 1.08.

This doesn't appear to have made any difference however.

I've also checked the version of the Thunderbolt drivers, which seem to be the latest available. I attach screenshots though so that you can verify.

Thanks very much. James


Razer.Caziel
  • I am the Lightbringer
  • April 21, 2021
@sharpRUBYDeer887 Everything appears to be in order. I'm starting to think that we should look into the eGPU's behavior instead. Do send me the serial number of the enclosure so I can forward this to our engineers.

*Thread locked to curb the conversation to PMs.

Cookie policy

We use cookies to enhance and personalize your experience. If you accept you agree to our full cookie policy. Learn more about our cookies.

 
Cookie settings